Braun ThermoScan Fix – Low Battery Warning Switch Off

We have a Braun Thermoscan infra-red (IR) thermometer that has been working perfectly for about five years. It started complaining about low batteries and shutting off, despite me replacing with new batteries that I checked had plenty of charge.

When I opened it, I discovered that the batteries connect to the circuit board via simple metal clip contacts, and that the contacts had some corrosion on them, which was preventing power from getting to the board, hence why it was complaining of low batteries.

So a very simple fix is to just clean the corrosion from the battery terminals inside the thermometer. You’ll need a Torx T9 screwdriver (Maplin, eBay, Amazon, maybe pound shops).

Start by removing the battery cover and the batteries. The image below shows the location of the screw in the battery compartment, that when removed will allow you to open the thermometer casing, which separates into the two halves.

Braun ThermoScan Repair 1

The next image (below) shows the location of four tabs (marked as ‘x’) that clip the two halves of the case together – they can be squeezed and prised apart gently to un-clip, and the case should come apart quite easily.

Note that for two of the clips, the top half of the case clips into the bottom half, and for the other two the bottom half clips into the top – it might help you figure out which bit to squeeze and which bit to prise, but in any case  I managed fine without that information.

Braun ThermoScan Repair 2

This image above also shows the contact points on the circuit board for the battery connection. This is where some corrosion had formed, and I could remove it simply by scraping lightly with a small screwdriver (the corner of a scourer would also have worked).

With the corrosion gone, the thermometer was working perfectly again. I just had to clip the case back together, replace the screw, then the batteries, and that was it all done.

This design probably applies to other variants of Braun Thermoscan thermometers – they all look roughly the same, just differing in features such as pre-heating, illuminated displays, reading memory, etc.

Braun: this is a design flaw. A bit of wire soldered on would have prevented this product from failing prematurely. One corner too many cut in production, I think.

57 Replies to “Braun ThermoScan Fix – Low Battery Warning Switch Off”

  1. Thanks for the info… my braun thermometer also having similiar problem but is not the contacts corrosive but the spring contacts got “loose” and having problem contact with the PCB board’s contacts. I bent it and it works like charm..

    1. Thanks for the fix description and the great pics! Using your guide I fixed our Thermoscan, which had been working flawlessly for eight years up until last week.

      1. Really pleased to hear that it helped. Hang on to that model of Thermoscan because the newer (and cheaper) ones don’t seem to be quite as good – the temperature can vary significantly between readings unless positioned perfectly, and there’s an illuminated display that makes it difficult to use in the low-light, because it shines in your eyes while you try to get the positioning right.

        More features make it less functional.

    2. Anybody know how to open the battery compartment of Braun type 6013 thermometer? I think my thermometer have the corrosion problem too.

    3. Same problem here with the bent contacts for the battery not making contact. Love this thermometer but being an electronics engineer and looking at the circuit board and overall design of how it powers up I agree with the comment that the design is poor for expecting a long term product life.

  2. A big “Thank you!”! Kevin. We have little kids at home and cannot live without a reliable ear thermometer and they are not cheap. Ours just stop working all together one day. We bought a new one, but was never as reliable. I tried your method to fix our old one – it worked like a charm. Thanks for the great photos, made it easy and possible for me!

    1. Glad it was helpful – the original model really is so much better. We have found that the newer model is a bit more reliable when the tip is pointing snugly into the ear canal, but the glare from the screen still makes it difficult to take temperatures at night, when kids are drowsy or sleeping.

  3. Big thanks to you! It really helps! Those photos makes it easy for me to follow the instructions. Its working fine now! Thanks a lot! ?

  4. My Braun thermometer’s temperature will not rise above 97.6 F or C. How can I fix it? I think the warranty is expiried by now.

    1. For medical devices, I wouldn’t recommend trying to replace components, unless I could be absolutely certain of why a component has failed. Better to simply replace it

  5. Thank you very much!!! Our Braun is nearly 10 years old already and stopped working with no warning. I followed your helpful instructions. Although I didn’t see any corrosion on the contacts, I scraped them with a flat screwdriver in any case and it works fine now.

  6. I used the thermometer for a while with low battery and it went flat dead.After replacing the batteries its not turning at all. Tried all the tricks on this forum. Any other thoughts ??

    1. I’d look for signs of leaking batteries, both at the battery terminals and on the board. Perhaps wipe the circuit board and connectors with a damp cotton bud to see if significant amounts of residue show up (there should be little to none). If the cotton bud picks up a lot of stuff anywhere, then clean everything gently but fully. Only use abrasives on the battery terminals. Try to leave the actual sensor entirely untouched. Pay attention to the buttons on the circuit board – if rusty fluid got into them, it could have created a short circuit that is making the controller chip think the button is continuously pressed (e.g. it could be stuck waiting for the button to be ‘released’). Wait until it’s fully dry before testing.

  7. Thanks for the information. My braun thermometer kept showing error. Thank god I found your forum I was actually thinking of buying a new one, I followed your instructions it was actually the spring contacts that got “loose” and was having problem to contact with the PCB board. I bent it a little and it works perfectly fine now.

  8. My braun thermometer keeps giving me a POS error OR it gives me a false reading of HI or 41°c. I have verified that it not the temperature with another thermometer.

    1. Seems plain faulty to me. While there may be components that could be replaced with good soldering skills and suitable replacement parts, my opinion is that it’s not worth the risk of false readings where someone might be running a high temperature. I would just replace it.

  9. Praise be to God, I found your post, tried your solution, and thank God it worked! Thank you so much for the detailed instructions and photos, wouldn’t have fixed mine without them. Thanks!

  10. I found out that my braun thermometer had a battery leak and corroded one of the metal contact on the circuit. Is there any suggestions to make it work again??

    1. Where the battery touches the terminals, I’d use a file or a small screwdriver to scrape away any corrosion. For contact pads on a circuit board, you have to be a lot more careful. I usually scrape very lightly with a screwdriver, or perhaps use the corner of a kitchen sponge (the scouring side). Remember to also check the metal that touches the pad, since this will probably be corroded too.

  11. Thanks so much. Repaired a thermometer over 10 years old! I used edge of a screwdriver then a pencil eraser. If I had more patience I would’ve used baking soda and water solution with a q tip and/or steel wool or fine sand paper.

  12. Thank you. Followed your description and fixed my thermo. Had same problem; failing battery was replaced but then no power and didn’t work. Follow this advice if you have a similar problem.

  13. Thank you so much – I didnt get battery corrosion but my 12 year old thermoscan “died” last year when changing batteries. Turns out it was the spring as well – i just bent it out a bit more, the battery fits more tightly and it works!!


  14. Thanks, I was just about to trash my braun so I figured what do I have to lose. I followed the directions and opened it up. I didn’t see any obvious corrosion but I went over the leads with a screwdriver anyway and once I put it back together it turned on right away. I tested it on several healthy people and it reads great. Thanks for helping me fix it.

  15. Thank you so much. I’m battling to get a screw driver to open it up but will try tom at hardware . These are so expensive abs it’s exactly 5 years that we have ours. With two small kids we need a reliable thermometer!! So will try your advice. I’m so glad I found your article thank you !

  16. Our thermoscan had been working well, but I am not 100% sure if it is me or just in daylight (I tried using in a dark room). But the light stays on until the moment it gets a reading and then the backlight turns off immediately. Bit of a pain as that is when you want the backlight on! Anyone had similair problem? Also I put cheap coles batteries into it, but they are brand new, so still should be fine?

    1. Assuming this is a more recent Thermoscan with a multi-coloured backlight, it might be that one of the LEDs is faulty – e.g. when you get an OK reading, the backlight turns green. If green is faulty then it will be as if the backlight turned off. Try faking a high temperature to see if it switches to red immediately on getting the reading.

      Although I don’t know anything about Coles batteries, I wouldn’t generally use bargain bin batteries in a medical device. They so rarely need changed that it’s better to pay for a quality brand. Keep the cheapos for everything else!

  17. Our Thermos can took a tumble yesterday…not from a great hight or force but the batteries fell out and the display panel slightly unclipped. However when put back together I get an alarm (doesn’t repeat) then constant flashing light and flashing display. I’ve held down and pushed all buttons, turned off and on but nothing works, I changed the batteries too and even the ear cover thing. Any ideas on how to fix this? Many thanks in advance.

    1. I don’t know what’s wrong, from your description, but it does seem to be at least behaving rationally. Often this kind of feedback indicates a broken connection somewhere. Perhaps the temperature sensor in the head of the unit has become detached? Are you sure you fully re-clipped the loose panel? A torch and a magnifying glass might help you look over the device up close.

  18. Thank you for the post. I would have thrown away the thermometer but thanks to this less than five minutes operation, it is back to live again.

  19. Thank you Kevin. I just fixed two old models with your tips. Scraped the metal contacts and good as new 🙂 My boy had a high fever and needed it to work.

  20. Hi Kevin, im having the same battery problem as yours in the same model. Trying to follow your fix, trying my best to open it, but once the screw is out, i dont know how to open it further. Im stuck. Can u pls help. Would love for u to put up a utube video so its easily follow able.

    I bought an omron thermometer meanwhile, and its horrible. Unless in the ear canal properly, it gives odd readings.
    I want my braun one to work again.
    Pls help.

    1. The clips on the case are marked in the picture – you should be able to click on the images to get a larger version (this was broken on the site when you looked, now fixed). You may have to look closely to see, but if you squeeze the top half of the case near the bottom end of the unit, you should be able to prise them apart quite easily. Similarly at the other end, squeeze the lower half of the case and prise. Neither pair of tabs need much force to separate – much easier to do than to describe!

  21. Thank you! Got my eight-year-old thermometer working again. In addition to scraping the contacts with a screwdriver, I used a small nail file built into a set of fingernail clippers.

  22. Thank you! My thermoscan had been working fine for the last five years but then appeared dead this morning – it just wouldn’t switch on even with fresh batteries. I cleaned the contacts with a small piece of emery cloth as your instructions and now it works again. It is awesome when people like you freely share your knowledge to help others – chapeau!

  23. Wow, thanks Kevin, I followed your very helpful instructions and it solved the problem I was having with our 10-year-old Braun thermometer. Your instructions are quite clear and, in my opinion, better than following a YouTube video.

  24. Thanks! I had almost given up when I found this page. I thought it was the end of the line and I’ve had this thermometer since around 2004 and it just started to fail. It would turn on and then a second later turn off. I took it apart and after trying some other online suggestions to no avail, found your page and, sure enough, the left connection was corroded. I wasn’t brave enough to use a screwdriver to scrape the circuit board, but a couple of Q-tips did the trick. Hopefully now I will get a few more years out of it. I haven’t heard great things about the new versions and I haven’t been really successful with the forehead thermometer.

  25. Really great instructions, thanks a lot! It helped me to fix my bent spring contacts. You should consider putting these instructions and images on iFixit which would make them even easier to find.

    1. I took a look at iFixit, and it does seem an OK site, but they assert the right to re-license contributors work which means that it could in future be sold on for advertising click-bait, sign-up dependent content, etc. I don’t know much about CC licensing, but anything I donate my free time to has to remain unconditionally free.

      However, since you have already dismantled your device once, you could easily write up something similar to post elsewhere.

  26. Thank you! You have been great help. Was kind of sad when I just could not get the Thermoscan 6022 to start up after changing batteries. Then I stumbled upon your article, followed your instructions and now it is working again.

  27. Thanks Kevin, problem exactly where you said Corrosion in between battery contacts and circuit board. I did add a drop off of DEOXIT to each contact .

    1. Thanks for the feedback. For anyone like me who’s unfamiliar with DeoxIt, it’s an electrical contact cleaner. However it’s pricey (very!), and I don’t think it’s worth buying specifically for this job, particularly since we’re just cleaning battery terminals (though it makes sense to use a contact cleaner if you do have one already).

  28. Thank you so much for explaining how to do this. It worked liked a charm. I have had my thermoscan since 2000 – impressive!

  29. Thanks Kevin as I followed your advice and my 6020 seems to be working again. It was saying lo then hi. I changed the batteries and then just got a constant error message or a reading of 41c! I was just about to throw it out when I found your advice. Followed it and it is working and giving realistic reads again. Thanks so much.

Leave a Reply to Tan Cancel reply

Your email address will not be published. Required fields are marked *